warming up testosterone before injections?

[nesto719]

Is it safe to warm up the testosterone before injecting, to make things go a little smoother?

[Megatron28]

Do you keep it at room temp? Do you want to warm it above room temp?

I don't warm it above room temp (and I find it goes in very smoothly) but I have read postings on this board by people who do warm it. And I should also mention that I store it at room temp.

[brother bundy]

just inject it no need to do all that

[BD7]

I think it depends what gauge pin your using. I warm mine since I use a 29g needle.. goes in in like 6-7 seconds.

[MrMitcheyBoy]

29G WTF thats tiny. just buy some 18G and save yourself the hassle

[clsmth700]

yes if using a smaller needle with thicker gear it actually does help to warm it

i use pharm test with 25guage so I have no issues and dont need to warm it up ... except one time my watson crashed actually so i heated it up to bring it back to life

what kind of gear you using?

[clsmth700]

just inject it no need to do all that

yep, pretty much this

[THE-DET-OAK]

There is nothing wrong with warning up the oil if you want. Simply warm up some water in a small bowl and then set the bottle in there. It will make the drawing process go a lot faster and it will make it easier to inject.

I personally do not do this but know many many guys that swear by it.

[juced_porkchop]

Is it safe to warm up the testosterone before injecting, to make things go a little smoother?

depends how you are warming it.
dont do anything stupid to get it warm. hold it in your hand for a few min (the vial) then swab it and draw shot.

[Illtemper]

29G WTF thats tiny. just buy some 18G and save yourself the hassle

Please dont tell me you pin with an 18g? Thats a harpoon man, that would leave to much scar tissue using those!

[MrMitcheyBoy]

Please dont tell me you pin with an 18g? Thats a harpoon man, that would leave to much scar tissue using those!

No fuck pinning with 18G, that's what I draw with. buy a bulk load of them and some 22G 1" and 1.5" for pinning.

[IMT staff]

No fuck pinning with 18G, that's what I draw with. buy a bulk load of them and some 22G 1" and 1.5" for pinning.

a 22 is a harpoon to me, I stick with 25 gauge.

[theguy9129]

23 for me and works fine, i wouldnt worry about warming.

[MrMitcheyBoy]

a 22 is a harpoon to me, I stick with 25 gauge.

I've just got used to it now so I don't feel a thing.

[zgx]

I've just got used to it now so I don't feel a thing.

27g for me, I don't warm up the oil.

[The AP]

I just started cycling and I use 28G and it took absolutely every bit of 15 minutes to draw and inject my oil. I'm going to have to try warming so I don't have to take a half hour out of my day to do a jab.

[theguy9129]

just drop down to a 25 or 23 and there will be no pain and will take about 5mins or less.

[zgx]

I just started cycling and I use 28G and it took absolutely every bit of 15 minutes to draw and inject my oil. I'm going to have to try warming so I don't have to take a half hour out of my day to do a jab.

Do what I do, order a syringe with a needle of 18g which you will use to draw and replace the needle with a 23g-27g to inject.

[juced_porkchop]

No fuck pinning with 18G, that's what I draw with. buy a bulk load of them and some 22G 1" and 1.5" for pinning.

why? with a 23g you can draw and pin with, perfect. and sometimes i switch tip to 25g 1" for delts (front and mid) or other smaller areas like that (front delt).
22-23g is good for both. to me 18g is too much for rubberstopper. I want my stuff as steril as possible, i am just uneasy when i see bits comming out as I have in the passed.
To pin with an 18g...... well I dont know I never tried that I think its crazy! HAHA

[juced_porkchop]

I just started cycling and I use 28G and it took absolutely every bit of 15 minutes to draw and inject my oil. I'm going to have to try warming so I don't have to take a half hour out of my day to do a jab.

but 22-23g and draw with then then put back this tip. or even just stick with the new pins. to use 28g for oil like this is nutz! you will be there for a while in some cases (depends on gear)

[theguy9129]

but 22-23g and draw with then then put back this tip. or even just stick with the new pins. to use 28g for oil like this is nutz! you will be there for a while in some cases (depends on gear)

I use a 21 then 23 i Like a new one for pinning to ensure its sharp

[MrMitcheyBoy]

why? with a 23g you can draw and pin with, perfect. and sometimes i switch tip to 25g 1" for delts (front and mid) or other smaller areas like that (front delt).
22-23g is good for both. to me 18g is too much for rubberstopper. I want my stuff as steril as possible, i am just uneasy when i see bits comming out as I have in the passed.
To pin with an 18g...... well I dont know I never tried that I think its crazy! HAHA

I see your point with the rubber stopper but touch wood hasn't happened yet. Will take your advice though and wait until my 18G have run out then just switch to the 22G to draw. There was a thread a couple days ago about pinning with 18G where a few blokes had to do it but there is no way in hell i'm pinning with that motherfucker.

[SquadLeader]

Theres no need to warm it.

[BD7]

I warm it for about a minute.. then draw and pin with the same 1" 29g slin pin. takes about 1 minute (or less) to draw and 15 seconds to pin .6 ml. easy and painless.

[MrMitcheyBoy]

I warm it for about a minute.. then draw and pin with the same 1" 29g slin pin. takes about 1 minute (or less) to draw and 15 seconds to pin .6 ml. easy and painless.

I've drawn and pinned with the same needle before. I'm never doing it again, was like trying to pin with a pencil. I had to really push it in to get deep in the muscle.